ETExamTower
Sign in
Q22Network Assurance

Refer to the exhibit. Which set of commands is needed to configure and verify the VRF for Site 1 Network A on router R1?

Question exhibit
← → navigate · a answer
Community votes
C
100% (4)
A
0% (0)
B
0% (0)
D
0% (0)
Discussion · 9
6
C is right because it's the only option where they assigned the VRF to an interface
5
Guys, one trick I learned from VRF Questions and answers and from Labs.. that in VRF we always give IP address after the VRF command, I mean the later command after VRF should be IP address. If you give the IP address first and then give VRF, then IP addresses will get removed.
C 3
Selected Answer: C C looks kind of OK, but all the options are weird.
3
A. R1#ip routing R1#(config)#ip vrf 100 R1#(config-vrf)#rd 100:1 R1#(config-vrf)# address family ipv4 ! R1(config)#interface Gi0/2 R1(config-if)#ip address 10.0.1.1 255.255.255.0 R1#show ip route B. R1#ip routing R1#(config)#ip vrf 100 ! R1(config)#interface Gi0/2 R1(config-if)#ip address 10.0.1.1 255.255.255.0 R1#showip route C. R1#ip routing R1#(config)#ip vrf 100 ! R1(config)#interface Gi0/2 R1(config-if)#ip vrf forwarding 100 R1(config-if)#ip address 10.0.1.1 255.255.255.0 R1#show ip vrf D. R1#ip routing R1#(config)#ip vrf 100 ! R1(config)#interface Gi0/2 R1(config-if)#ip address 10.0.1.1 255.255.255.0 R1#show ip vrf
3
C A. R1#ip routing R1#(config)#ip vrf 100 R1#(config-vrf)#rd 100:1 R1#(config-vrf)# address family ipv4 R1(config)#interface Gi0/2 R1(config-if)#ip address 10.0.1.1 255.255.255.0 R1#show ip route B. R1#ip routing R1#(config)#ip vrf 100 R1(config)#interface Gi0/2 R1(config-if)#ip address 10.0.1.1 255.255.255.0 R1#showip route C. R1#ip routing R1#(config)#ip vrf 100 R1(config)#interface Gi0/2 R1(config-if)#ip vrf forwarding 100 R1(config-if)#ip address 10.0.1.1 255.255.255.0 R1#show ip vrf D. R1#ip routing R1#(config)#ip vrf 100 R1(config)#interface Gi0/2 R1(config-if)#ip address 10.0.1.1 255.255.255.0 R1#show ip vrf
C 2
Selected Answer: C cisco_R3#show ip vrf Name Default RD Interfaces RED 1:1 cust_1 11:11 Et0/0.20 cust_2 22:22 Et0/0.30 cisco_R3#show runn int Et0/0.20 ! interface Ethernet0/0.20 encapsulation dot1Q 20 ip vrf forwarding cust_1 ip address 192.168.1.200 255.255.255.0 secondary ip address 192.168.1.1 255.255.255.0 end cisco_R3#show runn | s vrf ! ip vrf cust_1 rd 11:11 import ipv4 unicast map cust_2_to_cust_1
1
Answer is C.
C 1
Selected Answer: C correct, the only one that contains "vrf fowarding"
1
One of the discarding tricks is the command needed to verify the VRF. I remember that the show ip vrf command is the one we need in these cases.